AT-MIO-16D IO card Settings and Configuration

Card Type	Analog to digital timing converter
Chipset Controller	Unidentified
I/O Options	Analog input, analog output, digital input, digital output
Maximum DRAM	N/A

CONNECTIONS
Purpose	Location	Purpose	Location
34-pin interface connector	J1	100-pin I/O connector	J2

BASE I/O ADDRESS SELECTION
Address		U61/A5	U61/A6	U61/A7	U61/A8	U61/A9
»	220h	Off	On	On	On	Off
	100h	On	On	On	Off	On
	120h	Off	On	On	Off	On
	140h	On	Off	On	Off	On
	160h	Off	Off	On	Off	On
	180h	On	On	Off	Off	On
	360h	Off	Off	On	Off	Off
	380h	On	On	Off	Off	Off
	3A0h	Off	On	Off	Off	Off
	3C0h	On	Off	Off	Off	Off
	3E0h	Off	Off	Off	Off	Off
Note: A total of 255 base address settings are available. The switches are a binary representation of the decimal memory addresses. Switch A9 is the Most Significant Bit and switch A5 is the Least Significant Bit. The switches have the following decimal values: switch A9=512, A8=256, A7=128, A6=64, A5=32. Turn On the switches and add the values of the switches that are On to obtain the correct memory address. (Off=1, On=0)

DMA CHANNEL SELECTION (DMA 1)
DMA		W12/A	W12/B	W12/C	W12/D	W12/E	W12/F
»	6	Open	Open	Pins 1 & 2	Pins 1 & 2	Open	Open
	5	Open	Open	Open	Open	Pins 1 & 2	Pins 1 & 2
	7	Pins 1 & 2	Pins 1 & 2	Open	Open	Open	Open
	Disabled	Open	Open	Open	Open	Open	Open
Note: Pins designated are in the closed position.

DMA CHANNEL SELECTION (DMA 2)
DMA		W12/A	W12/B	W12/C	W12/D	W12/E	W12/F
»	7	Pins 2 & 3	Pins 2 & 3	Open	Open	Open	Open
	5	Open	Open	Open	Open	Pins 2 & 3	Pins 2 & 3
	6	Open	Open	Pins 2 & 3	Pins 2 & 3	Open	Open
	Disabled	Open	Open	Open	Open	Open	Open
Note: Pins designated are in the closed position.

INTERRUPT SELECTION (MIO-16 CIRCUITRY)
IRQ		W13/A	W13/B	W13/C	W13/D	W13/E	W13/F
»	10	Open	Open	Open	Open	Open	Open
	2/9	Open	Open	Open	Open	Open	1 & 2
	3	1 & 2	Open	Open	Open	Open	Open
	4	Open	1 & 2	Open	Open	Open	Open
	5	Open	Open	1 & 2	Open	Open	Open
	6	Open	Open	Open	1 & 2	Open	Open
	7	Open	Open	Open	Open	1 & 2	Open
	11	Open	Open	Open	Open	Open	Open
	12	Open	Open	Open	Open	Open	Open
	14	Open	Open	Open	Open	Open	Open
	15	Open	Open	Open	Open	Open	Open
	Disabled	Open	Open	Open	Open	Open	Open
Note: Pins designated are in the closed position.

INTERRUPT SELECTION (MIO-16 CIRCUITRY CON’T)
IRQ		W13/G	W13/H	W13/I	W13/J	W13/K
»	10	Closed	Open	Open	Open	Open
	2/9	Open	Open	Open	Open	Open
	3	Open	Open	Open	Open	Open
	4	Open	Open	Open	Open	Open
	5	Open	Open	Open	Open	Open
	6	Open	Open	Open	Open	Open
	7	Open	Open	Open	Open	Open
	11	Open	Closed	Open	Open	Open
	12	Open	Open	Closed	Open	Open
	14	Open	Open	Open	Closed	Open
	15	Open	Open	Open	Open	Closed
	Disabled	Open	Open	Open	Open	Open
Note: Pins designated are in the closed position.

INTERRUPT SELECTION (DIO -24 CIRCUITRY)
IRQ		W13/A	W13/B	W13/C	W13/D	W13/E	W13/F
»	5	Open	Open	2 & 3	Open	Open	Open
	2/9	Open	Open	Open	Open	Open	2 & 3
	3	2 & 3	Open	Open	Open	Open	Open
	4	Open	2 & 3	Open	Open	Open	Open
	6	Open	Open	Open	2 & 3	Open	Open
	7	Open	Open	Open	Open	2 & 3	Open
	10	Open	Open	Open	Open	Open	Open
	11	Open	Open	Open	Open	Open	Open
	12	Open	Open	Open	Open	Open	Open
	14	Open	Open	Open	Open	Open	Open
	15	Open	Open	Open	Open	Open	Open
	Disabled	Open	Open	Open	Open	Open	Open
Note: Pins designated are in the closed position.

INTERRUPT SELECTION (DIO-24 CIRCUITRY CON’T)
IRQ		W13/G	W13/H	W13/I	W13/J	W13/K
»	5	Open	Open	Open	Open	Open
	2/9	Open	Open	Open	Open	Open
	3	Open	Open	Open	Open	Open
	4	Open	Open	Open	Open	Open
	6	Open	Open	Open	Open	Open
	7	Open	Open	Open	Open	Open
	10	Closed	Open	Open	Open	Open
	11	Open	Closed	Open	Open	Open
	12	Open	Open	Closed	Open	Open
	14	Open	Open	Open	Closed	Open
	15	Open	Open	Open	Open	Closed
	Disabled	Open	Open	Open	Open	Open
Note: Pins designated are in the closed position.

DIO-24 CIRCUITRY INTERRUPT ENABLED CONFIGURATION
Setting		W14/A	W14/B	W14/C	W14/D
»	PC4	Open	Closed	Open	Open
	PC2	Open	Open	Closed	Open
	PC6	Closed	Open	Open	Open
	N/C (Disabled)	Open	Open	Open	Closed

ANALOG INPUT CONFIGURATION
Type		W6	W9
»	DIFF	Pins 1 & 3, 2 & 4, 5 & 6 closed	Pins 1 & 2 closed
	RSE	Pins 1 & 2, 3 & 4, 7 & 8 closed	Pins 2 & 3 closed
	NRSE	Pins 1 & 2, 3 & 5, 7 & 8 closed	Pins 2 & 3 closed

ANALOG INPUT POLARITY & RANGE CONFIGURATION
Range		Polarity	W1	W4
»	-10 to +10V	Bipolar input	Pins 1 & 2 closed	Pins 2 & 3 closed
	0 to +10V	Unipolar input	Pins 2 & 3 closed	Pins 1 & 2 closed
	-5 to +5V	Bipolar input	Pins 2 & 3 closed	Pins 2 & 3 closed

ANALOG OUTPUT CONFIGURATION
Type		W2 (Channel 1)	W3 (Channel 0)
»	Internal	Pins 2 & 3 closed	Pins 2 & 3 closed
	External	Pins 1 & 2 closed	Pins 1 & 2 closed

ANALOG OUTPUT POLARITY CONFIGURATION
Type		W7 (Channel 1)	W8 (Channel 0)
»	Bipolar	Pins 1 & 2 closed	Pins 1 & 2 closed
	Unipolar	Pins 2 & 3 closed	Pins 2 & 3 closed
Note: Use this table in conjunction with the table below to set jumpers for Bipolar & Unipolar mode selection.

BIPOLAR & UNIPOLAR OUTPUT MODE CONFIGURATION
Mode		W10 (Channel 0)	W11 (Channel 1)
»	Two’s Complement	Pins 1 & 2 closed	Pins 1 & 2 closed
	Straight Binary (Unipolar)	Pins 2 & 3 closed	Pins 2 & 3 closed
Note: Bipolar can use both modes, while Unipolar uses the straight binary mode only.

RTSI BUS CLOCK CONFIGURATION
Setting		W5/A	W5/B	W5/C
»	Use local oscillator board signal	Open	Closed	Closed
	Receive the RTSI bus signal	Closed	Open	Closed
	Drive RTSI bus & board/OSC	Closed	Closed	Open