CS-ETHERNET-KARTE COMBO PREMIUM Network Card Settings and Configuration

NIC Type:	Ethernet
Transfer Rate:	10Mbps
Data Bus:	16-bit ISA
Topology:	Linear Bus Star
Wiring Type	RG58A/U 50ohm coaxial Shielded/unshielded twisted pair
Boot ROM	Available

HARDWARE/SOFTWARE CONFIGURABLE SELECT
Setting		J1
»	Card is software-configured	Open
	Card is hardware (jumper) configured	Closed

BOOT ROM ADDRESS - J2
Address		Jumper A	Jumper B	Jumper C	Jumper D	Jumper F
»	Disabled	Open	Open	Open	Open	Closed
	C0000h	Open	Closed	Open	Open	Open
	C4000h	Closed	Closed	Open	Open	Open
	C8000h	Open	Open	Closed	Open	Open
	CC000h	Closed	Open	Closed	Open	Open
	D0000h	Open	Closed	Closed	Open	Open
	D4000h	Closed	Closed	Closed	Open	Open
	D8000h	Open	Open	Open	Closed	Open
	DC000h	Closed	Open	Open	Closed	Open

I/O ADDRESS - J3
Address		Jumper A	Jumper B	Jumper C
»	300h	Open	Open	Open
	240h	Open	Closed	Open
	280h	Closed	Closed	Open
	2C0h	Open	Open	Closed
	320h	Closed	Open	Closed
	340h	Open	Closed	Closed
	360h	Closed	Closed	Closed

INTERRUPT SELECT - J3
IRQ		Jumper D	Jumper E	Jumper F
»	IRQ3	Open	Open	Open
	IRQ4	Closed	Open	Open
	IRQ5	Open	Closed	Open
	IRQ7	Closed	Closed	Open
	IRQ9	Open	Open	Closed
	IRQ11	Open	Closed	Closed
	IRQ12	Closed	Closed	Closed

FAST-READ MODE
Setting		J3/jumper G
»	Disabled	Open
	Enabled	Closed

NE2000/WD MODE SELECT
Setting		J3/jumper H
»	NE2000 mode	Open
	WD mode	Closed

WIRING TYPE SELECT
Setting		J4/jumper A
»	BNC (coaxial)	Closed
	Shielded/unshielded twisted-pair	Open

TWISTED PAIR STATUS LED (D4)
Setting		J4/jumper C
»	Disabled	Open
	Enabled	Closed

IOCS16 SIGNAL
Setting		J4/jumper D
»	Disabled	Open
	Enabled	Closed

IOCHRDY SIGNAL
Setting		J4/jumper E
»	Disabled	Open
	Enabled	Closed

BNC-TYPE - J8
Setting		Jumper A	Jumper B	Jumper C
»	RG58A/U 50ohm coaxial	All pins open	Pins 2 & 3 closed	Pins 2 & 3 closed
	RG62A/U 93ohm coaxial	All pins open	Pins 1 & 2 closed	Pins 1 & 2 closed

BOOT ROM TYPE
Setting		J10
»	2764 chip	Pins 2 & 3 closed
	27256 chip	Pins 1 & 2 closed

16/64KB RAM VERSION
Setting	J11
16KB	Pins 1 & 2 closed
64KB	Pins 2 & 3 closed

FACTORY CONFIGURED SETTINGS
Jumper	Setting
J2/jumper E	Open
J2/jumper G	Open
J2/jumper H	Open
J4/jumper B	Open
J4/jumper F	Open
J4/jumper G	Open
J4/jumper H	Open

DIAGNOSTIC LEDS
LED	Color	Status	Condition
D1	Red	On	Data is being transmitted
D2	Green	On	Data is being received
D3	Red	On	Collision detected on network
D4	Green	On	Twisted pair network connection is good
D5	Red	On	Twisted pair network connection is broken